Заправка картриджей, ремонт оргтехники, лазерных, струйных, сублимационных принтеров, 3D принтеров, плоттеров, копиров, МФУ, факсов.

SkyCopy studio

тел. +7 (985) 432-31-30

Руководство по устранению неполадок "ВЫЗВАТЬ СЕРВИС" Panasonic

CALL SERVICE Troubleshooting Guide

Руководство по устранению ошибок "ВЫЗВАТЬ СЕРВИС" Panasonic

 

ОШИБКА ОПИСАНИЕ ПРОБЛЕМЫ СБРОС ПОСЛЕ ПЕРЕЗАГРУЗКИ СЕРВИСНЫЙ РЕЖИМ
Call Service 1 (Вызвать сервис 1) Polygon motor error in LSU (Laser Scanning Unit), Мотор вращающегося зеркала лазерного блока Да *639
Call Service 2 (Вызвать сервис 2)

Laser beam error in LSU (Laser Scanning Unit)
Нет лазерного излучения в лазерном блоке

Да *639
Call Service 3 (Вызвать сервис 3) Fuser unit cannot heat up
Печка не прогревается
нет (МЕНЮ # 9000 * 550 или (*529) и нажать клавишу СТАРТ или ОК......Выход - СТОП, СТОП, СТОП)
 Once “CALL SERVICE 3” is displayed, it does not disappear until the Factory Setup or Service Function #529 is executed. Therefore Service Function #529 should not be executed before the confirmation, and #529 should be done after the countermeasure.
*550 or *529 or *655
Call Service 4 (Вызвать сервис 4) FAN motor error (Fuser Fan)
Мотор вентилятора
Да *677
Call Service 5 (Вызвать сервис 5) DC Motor Drive
Главный мотор
Да *556
Call Service 6 (Вызвать сервис 6) Charge voltage is abnormal
Аномальное напряжение
  *628
Call Service 7 (Вызвать сервис 7)      
Call Service 8 (Вызвать сервис 8)      
Call Service 11 (Вызвать сервис 11) PSU fan motor error    *677
Call Service 12 (Вызвать сервис 12) Color Motor Control Circuit  Алгоритм поиска и устранения неисправности "Вызвать Сервис 12"  *556
Call Service 13 (Вызвать сервис 13) FTR home sensor    *556-55
Call Service 14 (Вызвать сервис 14) Solenoid driver error    
Call Service 15 (Вызвать сервис 15) Registration and Paper pick home sensor    *556-50
Call Service 16 (Вызвать сервис 16) Fuse error of color drum cartridge    
Call Service 17 (Вызвать сервис 17) OPC First use sensor problem.    
Call Service 18 (Вызвать сервис 18) Watch dog error of motor or heater    
Call Service 19 (Вызвать сервис 19) OPC home sensor or Monochrome drum driving solenoid error    *556-54
Call Service 20 (Вызвать сервис 20) Toner LED error    *823
Call Service 22 (Вызвать сервис 22) Toner first use detection    
 CHECK DOCUMENT  The document was not fed into the unit properly. Remove the document, then press [Stop] to clear the message. Re-insert the document. If misfeeding occurs frequently, clean the document feeder rollers and try again.    
       

 

 

Dorus.ru
Рейтинг@Mail.ru